Скачать прошивку для роутера smart box giga

На боковой панели роутера есть кнопка с названием RST/WPS. Её надо нажать и удерживать в течение 20 секунд — роутер начнёт сброс настроек.

Шаг 1

Откройте браузер и введите в адресную строку 192.168.1.1. Вы попадёте на страницу приветствия. Нажмите кнопку «Продолжить».

Шаг 2

Роутер предложит вам ввести имя пользователя и пароль. Введите в первое поле admin, во второе также admin. Нажмите кнопку «Войти».

Шаг 3

Вы попадёте в главное меню роутера. Выберите пункт «Расширенные настройки».

Шаг 4

Во вкладке «Основные настройки», откройте раздел «Файл конфигурации» и нажмите кнопку «Сброс». Роутер начнёт сброс настроек.

The Beeline SmartBox GIGA is a wireless router based on the MT7621 platform with USB 3.0 port. While it can be acquired for relatively low cost (especially on avito.ru) compared to other units with similar specifications.

It’s recommended to make a mtd backup before you start:

1. Get SSH access

2. Set up a tftp server (e.g. tftpd64 for windows)

3. Connect to a router using SSH shell and run the following commands:

cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10 11; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2

10.0.0.2 — IP of the tftp server

4. Check backups in your tftp root folder.

CAUTION:

If you have any third-party firmware (e.g. Padavan, Keenetic, AsusWrt, non-official OpenWrt community builds (especially for Breed bootloader) etc.) installed on your device it’s strongly recommended to restore original OEM firmware (including bootloader, EEPROM, partition map etc.) from your backup before you start the OpenWrt installation on your device.

1. Install stock Beeline v.1.0.02 firmware twice

2. Remove all dots from the OpenWrt factory image file name

3. Install OpenWrt factory image via the original web interface

Remark:
You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update.

1. Login to the router web interface (admin:admin)

2. Navigate to Settings → WAN → Add static IP interface (e.g. 10.0.0.1/255.255.255.0)

3. Navigate to Settings → Remote cotrol → Add SSH, port 22, 10.0.0.0/255.255.255.0 and interface created before

4. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the ethernet cable to the WAN port of the router

5. Connect to the router using SSH shell (SuperUser:SQxxxxxxxxxx, where SQxxxxxxxxxx is the serial number from the backplate label)

6. Run in SSH shell:

sh

If you don’t have a GUI (LuCI) available, you can alternatively upgrade via the command line.
There is a command line method for upgrading:

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

cd /tmp
sysupgrade /tmp/sysupgrade.bin

1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:

printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely.

1. Compile sercomm-recovery under the Linux:

git clone https://github.com/danitool/sercomm-recovery.git
make

2. Connect the router with a cable and run sercomm-recovery:

sudo ./sercomm-recovery enp0s3 recovery_giga_stock.bin

where enp0s3 — network interface connected the router, ifconfig — list on available network interfaces

3. Wait until the router is flashed and rebooted.

Download ready recovery images for Sercomm devices.

Contcat all mtd backup into one file:

cat mtd0 mtd1 mtd2 mtd3 mtd4 mtd5 mtd6 mtd7 mtd8 mtd9 mtd10 mtd11 > full.bin

Add OOB data:

bbe -b ":512" -e "A 0000000000000000" full.bin -o full-oob.bin

1. Run tftp server on IP 10.10.10.3/24

2. Rename initramfs OpenWrt image to test.bin and copy it to the tftp root

3. Connect UART, power on the router and interrupt the boot process by pressing any key

4. In U-Boot command console run:

tftpboot
bootm

5. Wait until OpenWrt boots

6. Make sysupgrade to install OpenWrt on NAND flash of the router

The default network configuration is:

→ hardware.button on howto use and configure the hardware button(s).
Here, we merely name the buttons, so we can use them in the above Howto.

The Beeline Smartbox GIGA has the following buttons:

Front:

Back:

Backside label:

Note: This will void your warranty!

There are crews on the backplate. There are also clips around the edge of the case you will need to prize open, using, for example, a plastic card.

Main PCB:

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:

Insert photo of PCB with markings for JTAG port

Input conditions:

You will need:

After executing each command, carefully read its output before executing the next one.

1. Enter the Breed telnet shell (IP: 192.168.1.1)

2. Download dynamic partition map backup from your http server and write it:

wget http://192.168.1.2/mtd1.bin

flash erase 0x100000 0x200000

flash write 0x100000 0x80001000 0x100000

2. Download Factory backup from your http server and write it:

wget http://192.168.1.2/mtd2.bin

flash write 0x200000 0x80001000 0x100000

3. Download u-boot bootloader backup from your http server and write it:

The most dangerous part of the instruction. Be extremely careful.

wget http://192.168.1.2/mtd0.bin

flash erase 0x0 0x100000

flash write 0x0 0x80001000 0x100000

4. Check written data and reboot:

flash dump 0x0

flash dump 0x100000

flash dump 0x200000

5. Use sercomm-recovery utility for stock firmware recovery

Problem

Hanging of Fibocom L860-GL USB modem under high upload.

Solution

Solder the C1840 capacitor in the 5V USB power circuit. The place for it is already exists. Keep the polarity of the capacitor!
Rating 100-330 uF x 16V.

===================================================================

MT7621 stage1 code Mar 12 2015 14:42:52 (ASIC)

CPU=50000000 HZ BUS=16666666 HZ

==================================================================

Change MPLL source from XTAL to CR…

do MEMPLL setting..

MEMPLL Config : 0x11100000

3PLL mode + External loopback

=== XTAL-40Mhz === DDR-1200Mhz ===

PLL3 FB_DL: 0x0, 1/0 = 599/425 01000000

PLL2 FB_DL: 0xc, 1/0 = 630/394 31000000

PLL4 FB_DL: 0x12, 1/0 = 704/320 49000000

do DDR setting..[00320381]

Apply DDR3 Setting…(use customer AC)

0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120

———————————————————————————

0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

000E:| 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1

000F:| 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1

0010:| 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0

0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0

0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

DRAMC_DQSCTL1[0e0]=14000000

DRAMC_DQSGCTL[124]=80000000

rank 0 coarse = 16

rank 0 fine = 40

B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0

opt_dle value:9

DRAMC_DDR2CTL[07c]=C287221D

DRAMC_PADCTL4[0e4]=000022B3

DRAMC_DQIDLY1[210]=0B0C0B0C

DRAMC_DQIDLY2[214]=060C090D

DRAMC_DQIDLY3[218]=0D060A05

DRAMC_DQIDLY4[21c]=0B050C07

DRAMC_R0DELDLY[018]=00002424

==================================================================

RX DQS perbit delay software calibration

==================================================================

1.0-15 bit dq delay value

==================================================================

bit| 0 1 2 3 4 5 6 7 8 9

—————————————

0 | 11 9 11 11 13 9 12 6 1 7

10 | 5 11 7 9 5 8

—————————————

==================================================================

2.dqs window

x=pass dqs delay value (min~max)center

y=0-7bit DQ of every group

input delay:DQS0 =36 DQS1 = 36

==================================================================

bit DQS0 bit DQS1

0 (1~69)35 8 (1~64)32

1 (2~67)34 9 (1~65)33

2 (1~70)35 10 (2~68)35

3 (1~71)36 11 (2~67)34

4 (1~71)36 12 (2~70)36

5 (2~71)36 13 (0~66)33

6 (1~71)36 14 (2~70)36

7 (1~71)36 15 (1~66)33

==================================================================

3.dq delay value last

==================================================================

bit| 0 1 2 3 4 5 6 7 8 9

—————————————

0 | 12 11 12 11 13 9 12 6 5 10

10 | 6 13 7 12 5 11

==================================================================

==================================================================

TX perbyte calibration

==================================================================

DQS loop = 15, cmp_err_1 = ffff0000

dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1

dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2

DQ loop=15, cmp_err_1 = ffff0000

dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1

dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2

byte:0, (DQS,DQ)=(8,8)

byte:1, (DQS,DQ)=(8,8)

DRAMC_DQODLY1[200]=88888888

DRAMC_DQODLY2[204]=88888888

20,data:88

[EMI] DRAMC calibration passed

===================================================================

MT7621 stage1 code done

CPU=50000000 HZ BUS=16666666 HZ

===================================================================

U-Boot 1.1.3 (Aug 13 2019 — 15:27:14)

Board: Ralink APSoC DRAM: 256 MB

rt2880 uboot v0.00e04 05/25/2006

SERIAL_CLOCK_DIVISOR =16

kaiker,,CONFIG_BAUDRATE =57600

SDRAM SIZE:10000000

Top of RAM usable for U-Boot at: 8fd00000

Reserving 425k for U-Boot at: 8fc94000

Reserving 1028k for malloc() at: 8fb93000

Reserving 44 Bytes for Board Info at: 8fb92fd4

Reserving 36 Bytes for Global Data at: 8fb92fb0

Reserving 128k for boot params() at: 8fb72fb0

Stack Pointer at: 8fb72f98

relocate_code Pointer at: 8fc94000

Config XHCI 40M PLL

Now running in RAM — U-Boot at: 8fc94000

monitor_flash_len =116956

Command «mdio»: 0xa02062f0 => 0x8fc9a2f0

Command «nand»: 0xa020be4c => 0x8fc9fe4c

Command «reset»: 0xa0215d6c => 0x8fca9d6c

Command «go»: 0xa020d7f8 => 0x8fca17f8

Command «bootm»: 0xa020e054 => 0x8fca2054

Command «loadb»: 0xa020ed14 => 0x8fca2d14

Command «tftpboot»: 0xa020f344 => 0x8fca3344

Command «nm»: 0xa020fb48 => 0x8fca3b48

Command «mm»: 0xa020fbac => 0x8fca3bac

Command «md»: 0xa020fc10 => 0x8fca3c10

Command «mcmp»: 0xa020f744 => 0x8fca3744

Command «saveenv»: 0xa02102f4 => 0x8fca42f4

Command «setenv»: 0xa0210c64 => 0x8fca4c64

Command «printenv»: 0xa0210344 => 0x8fca4344

Command «?»: 0xa0210f38 => 0x8fca4f38

Command «help»: 0xa0210f38 => 0x8fca4f38

Command «version»: 0xa0210df8 => 0x8fca4df8

Command «sc_upgrade_flag»: 0xa0213d78 => 0x8fca7d78

Command «sc_boot»: 0xa0213db0 => 0x8fca7db0

Command «sc_nand»: 0xa0213de8 => 0x8fca7de8

Command «sc_eth_test»: 0xa0213e24 => 0x8fca7e24

Command «sc_phy»: 0xa0213e60 => 0x8fca7e60

Command «sc_time»: 0xa0213e9c => 0x8fca7e9c

Command «sc_btver»: 0xa0213ed4 => 0x8fca7ed4

Command «sc_fl_map»: 0xa0213f10 => 0x8fca7f10

Command «sc_endian»: 0xa0213f4c => 0x8fca7f4c

Command «sc_gpio»: 0xa0213f88 => 0x8fca7f88

Command «sc_led»: 0xa0213fc4 => 0x8fca7fc4

Command «sc_mem_usage_info»: 0xa021390c => 0x8fca790c

Command «sc_dl»: 0xa0214000 => 0x8fca8000

Allocate 16 byte aligned buffer: 8fcca3f0

Enable NFI Clock

# MTK NAND # : Use HW ECC

NAND ID [C2 F1 80 95 02]

Device found in MTK table, ID: c2f1, EXT_ID: 809502

Support this Device in MTK table! c2f1

select_chip

[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16

Signature matched and data read!

load_fact_bbt success 1023

load fact bbt success

[mtk_nand] probe successfully!

mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8

*** Warning — bad CRC, using default environment

icache: sets:256, ways:4, linesz:32 ,total:32768

dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 880 MHZ ####

estimate memory size =256 Mbytes

#Reset_MT7530

Load Standalone from 40000

SC_DEBUG: Nand Partition Table Magic Found at 100000.

e[31m******************************************

Uboot StandAlone Entry

******************************************e[0m

GPIO init

*********************************************************

Press any key to enter Boot Command Interface

*********************************************************

0

SC_DEBUG: Nand Partition Table Magic Found at 100000.

e[31m******************************************

Uboot StandAlone Entry

******************************************e[0m

***************************************************

S2 Boot Version 0100, at Aug 13 2019, 15:27:09

***************************************************

SC_DEBUG: Nand Partition Table Magic Found at 100000.

Ethernet is closed .

Entering Firmware : Everything is OK.

*************************************

Boot Flag : Sercomm1

*************************************

Fw header Magic check OK!

FW header checksum should: 0x47b7b0fe, crc32 result: 0x47b7b0fe, Fw header CRC check OK!

kernel : real offset: 0x00a20100, data length: 0x003dd3f8,checksum :0x67d1e2fd

kernel result: 0x67d1e2fd, kernel check sum ok!

rootfs: real offset: 0x02820000, data length: 0x0093e000, checksum :0x81bdb3ef

rootfs result: 0x81bdb3ef, rootfs check sum ok!

Kernel Addr : 0xbca20100

## Booting image at bca20100 …

Image Name: Linux Kernel Image

Image Type: MIPS Linux Kernel Image (lzma compressed)

Data Size: 4051896 Bytes = 3.9 MB

Load Address: 81001000

Entry Point: 816eb7a0

Verifying Checksum … OK

Uncompressing Kernel Image … OK

kernel addr :0xBCA20100

No initrd

## Transferring control to Linux (at address 816eb7a0) …

## Giving linux memsize in MB, 256

Starting kernel …

LINUX started…

THIS IS ASIC

SDK 5.0.S.0
Linux version 3.10.14 (sercomm@pavel) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Tue Mar 10 20:27:48 MSK 2020

The CPU feqenuce set to 880 MHz
GCMP present
CPU0 revision is: 0001992f (MIPS 1004Kc)
Software DMA cache coherency
Determined physical RAM map:
memory: 0fffc000 @ 00000000 (usable)
memory: 00004000 @ 0fffc000 (reserved)
Zone ranges:
DMA [mem 0x00000000-0x00ffffff]
Normal [mem 0x01000000-0x0fffbfff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x0fffbfff]
Detected 3 available secondary CPU(s)
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
PERCPU: Embedded 7 pages/cpu @81ca0000 s6720 r8192 d13760 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65020
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Writing ErrCtl register=00030010
Readback ErrCtl register=00030010
Memory: 248880k/262128k available (7126k kernel code, 13248k reserved, 3223k data, 268k init, 0k highmem)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop… 577.53 BogoMIPS (lpj=1155072)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
launch: starting cpu1
launch: cpu1 gone!
CPU1 revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Synchronize counters for CPU 1: done.
launch: starting cpu2
launch: cpu2 gone!
CPU2 revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Synchronize counters for CPU 2: done.
launch: starting cpu3
launch: cpu3 gone!
CPU3 revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Synchronize counters for CPU 3: done.
Brought up 4 CPUs
devtmpfs: initialized
NET: Registered protocol family 16
release PCIe RST: RALINK_RSTCTRL = 7000000
PCIE PHY initialize
***** Xtal 40MHz *****
start MT7621 PCIe register access
RALINK_RSTCTRL = 7000000
RALINK_CLKCFG1 = 77ffeff8

*************** MT7621 PCIe RC mode *************
PCIE2 no card, disable it(RST&CLK)
pcie_link status = 0x3
RALINK_RSTCTRL= 3000000
*** Configure Device number setting of Virtual PCI-PCI bridge ***
RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
PCIE0 enabled
PCIE1 enabled
interrupt enable status: 300000
Port 1 N_FTS = 1b105000
Port 0 N_FTS = 1b105000
config reg done
init_rt2880pci done
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:00.0: BAR 0: can’t assign mem (size 0x80000000)
pci 0000:00:01.0: BAR 0: can’t assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 9: assigned [mem 0x60000000-0x601fffff pref]
pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit pref]
pci 0000:01:00.0: BAR 2: assigned [mem 0x60100000-0x60103fff 64bit pref]
pci 0000:01:00.0: BAR 4: assigned [mem 0x60104000-0x60104fff 64bit pref]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [mem 0x60000000-0x601fffff pref]
pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
pci 0000:00:01.0: PCI bridge to [bus 02]
pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff]
PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 60300000
res[1]->end = 6030ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
BAR0 at slot 1 = 0
bus=0x0, slot = 0x1
res[0]->start = 0
res[0]->end = 0
res[1]->start = 60310000
res[1]->end = 6031ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0, irq=0x4
res[0]->start = 60000000
res[0]->end = 600fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 60100000
res[2]->end = 60103fff
res[3]->start = 0
res[3]->end = 0
res[4]->start = 60104000
res[4]->end = 60104fff
res[5]->start = 0
res[5]->end = 0
bus=0x2, slot = 0x1, irq=0x18
res[0]->start = 60200000
res[0]->end = 602fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
4 CPUs re-calibrate udelay(lpj = 1167360)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.30 [Flags: R/W].
fuse init (API version 7.22)
msgmni has been set to 486
io scheduler noop registered (default)
reg_int_mask=0, INT_MASK= 0
HSDMA_init

hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000

hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000
TX_CTX_IDX0 = 0
TX_DTX_IDX0 = 0
RX_CRX_IDX0 = 3ff
RX_DRX_IDX0 = 0
set_fe_HSDMA_glo_cfg
HSDMA_GLO_CFG = 465
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
serial8250: ttyS2 at MMIO 0x1e000e00 (irq = 28) is a 16550A
brd: module loaded
MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
Allocate 16 byte aligned buffer: 81a77dd0
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C2 F1 80 95 02, 00809502]
Device found in MTK table, ID: c2f1, EXT_ID: 809502
alloctare : (mtd->writesize + mtd->oobsize) * page_per_block is 135168
Support this Device in MTK table! c2f1

NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Macronix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Scanning device for bad blocks
Bad eraseblock 22 at 0x0000002c0000
Signature matched and data read!
load_fact_bbt success 1023
00 00 00 00 00 30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SC_DEBUG: Go to read Magic at 100000
page: 200
SC_DEBUG: NAND Partition Table Magic was found at 100000.
page: 201
SC_DEBUG: part 0,real_offset 00000000, real_length 00100000
page: 201
SC_DEBUG: part 1,real_offset 00100000, real_length 00100000
page: 201
SC_DEBUG: part 2,real_offset 00200000, real_length 00120000
page: 201
SC_DEBUG: part 3,real_offset 00320000, real_length 00100000
page: 201
SC_DEBUG: part 4,real_offset 00420000, real_length 00600000
page: 201
SC_DEBUG: part 5,real_offset 00a20000, real_length 00600000
page: 201
SC_DEBUG: part 6,real_offset 01020000, real_length 01800000
page: 201
SC_DEBUG: part 7,real_offset 02820000, real_length 01800000
page: 201
SC_DEBUG: part 8,real_offset 04020000, real_length 00800000
page: 201
SC_DEBUG: part 9,real_offset 04820000, real_length 00c00000
page: 201
SC_DEBUG: part 10,real_offset 05420000, real_length 02800000
page: 201
SC_DEBUG: part 11,real_offset 07c20000, real_length 00360000
Creating 12 MTD partitions on «MT7621-NAND»:
0x000000000000-0x000000100000 : «Boot Loader»
0x000000100000-0x000000200000 : «dynamic partition map»
0x000000200000-0x000000320000 : «Factory»
0x000000320000-0x000000420000 : «Boot Flag»
0x000000420000-0x000000a20000 : «Kernel 1»
0x000000a20000-0x000001020000 : «Kernel 2»
0x000001020000-0x000002820000 : «File System 1»
0x000002820000-0x000004020000 : «File System 2»
0x000004020000-0x000004820000 : «Configuration/log»
0x000004820000-0x000005420000 : «application tmp buffer (Ftool)»
0x000005420000-0x000007c20000 : «container»
0x000007c20000-0x000007f80000 : «bad block reserved»
[mtk_nand] probe successfully!
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
register mt_drv

=== pAd = c0181000, size = 8000960 ===

<— RTMPAllocAdapterBlock, Status=0
pAd->PciHif.CSRBaseAddress =0xc0080000, csr_addr=0xc0080000!
RTMPInitPCIeDevice():device_id=0x7663
mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a01, pAd->ChipID=0x7663
mt7663_init()—>
<—mt7663_init()
<— RTMPAllocTxRxRingMemory, Status=0
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
add_oom_notifier()
rdm_major = 253
set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1
GMAC1_MAC_ADRH — : 0x0000000c
GMAC1_MAC_ADRL — : 0x43288071
Ralink APSoC Ethernet Driver Initilization. v3.1 4096 rx/tx descriptors allocated, mtu = 1500!
set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1
GMAC1_MAC_ADRH — : 0x0000000c
GMAC1_MAC_ADRL — : 0x43288011
<0> !! create link_status PROC !!!!!
PROC INIT OK!
usbcore: registered new interface driver usb-storage
Ralink APSoC Hardware Watchdog Timer
GACT probability on
Mirror/redirect action on
Failed to load ipt action
u32 classifier
Performance counters on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3888 buckets, 15552 max)
ctnetlink v0.93: registering with nfnetlink.
NF_TPROXY: Transparent proxy support initialized, version 4.1.0
NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: Creating netns size=776 id=0
IPVS: ipvs loaded.
gre: GRE over IPv4 demultiplexor driver
ip_tables: (C) 2000-2006 Netfilter Core Team
Type=Linux
arp_tables: (C) 2002 David S. Miller
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
Ebtables v2.0 registered
l2tp_core: L2TP core driver, V2.0
l2tp_ppp: PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
Sercomm dual images: bootflag=Sercomm1, choose /dev/mtdblock7 as rootfs
VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
devtmpfs: mounted
Freeing unused kernel memory: 268K (81a1d000 — 81a60000)

init started: BusyBox v1.15.3 ()

starting pid 51, tty »: ‘/etc/rcS’
mount: mounting usbfs on /proc/bus/usb failed: No such file or directory
register rlt_drv

=== pAd = c0e81000, size = 1295256 ===

<— RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
<— RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0d80000, csr_addr=0xc0d80000!
device_id =0x7603
RtmpChipOpsHook(474): Not support for HIF_MT yet!
mt7603_init()—>
mt_bcn_buf_init(224): Not support for HIF_MT yet!
<—mt7603_init()
hal_wd: module license ‘sercomm’ taints kernel.
Disabling lock debugging due to kernel taint
Init system monitor…
Sercomm HWIO Driver: loaded successfully
nUBI: attaching mtd8 to ubi8
UBI: scanning is finished
UBI: attached mtd8 (name «Configuration/log», size 8 MiB) to ubi8
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 67/49, WL threshold: 4096, image sequence number: 679372223
UBI: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 20

UBI: background thread «ubi_bgt8d» started, PID 93
UBI device number 8, total 64 LEBs (8126464 byteUBIFS: background thread «ubifs_bgt8_0» started, PID 95
s, 7.8 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 8, volume 0, name «0»
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 3809280 bytes (3 MiB, 30 LEBs), journal size 3428352 bytes (3 MiB, 27 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID D569DB63-F2CC-4411-9F53-3FA4254DC41A, small LPT model
Started WatchDog Timer.
SERIAL NUMBER: SQ1731F7F722
FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF
Raeth v3.1 (Tasklet)
phy_free_head is 0xc9c000!!!
phy_free_tail_phy is 0xc9dff0!!!
txd_pool=a0ca8000 phy_txd_pool=00CA8000
ei_local->skb_free start address is 0x8e9026cc.
free_txd: 00ca8010, ei_local->cpu_ptr: 00CA8000
POOL HEAD_PTR | DMA_PTR | CPU_PTR
—————-+———+———
0xa0ca8000 0x00CA8000 0x00CA8000

phy_qrx_ring = 0x00c9e000, qrx_ring = 0xa0c9e000

phy_rx_ring0 = 0x00cb0000, rx_ring[0] = 0xa0cb0000
MT7530 Reset Completed!!
change HW-TRAP to 0x117c8f
set LAN/WAN WLLLL
GMAC1_MAC_ADRH — : 0x000060ce
GMAC1_MAC_ADRL — : 0x866eb816
GDMA2_MAC_ADRH — : 0x0000000c
GDMA2_MAC_ADRL — : 0x432880ba
eth3: ===> VirtualIF_open
MT7621 GE2 link rate to 1G
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
GDMA2_FWD_CFG = 20710000
sc_lan_vlan_id = 1
sc_wan_vlan_id = 2
sc_special_vlan_id = 3
sc_host_queue = 3
rc_cmd=/usr/sbin/rc syslogd start
Chain ‘FORWARD_WIFI’ doesn’t exist.
Chain ‘INPUT_WIFI’ doesn’t exist.
rc_cmd=/usr/sbin/rc wan_switch start
rc_cmd=/usr/sbin/rc lan_switch start
rc_cmd=/usr/sbin/rc dnrd start
rc_cmd=/usr/sbin/rc wlan start
============guest<2> is disabled============
============guest<3> is disabled============
============guest<4> is disabled============
============guest<6> is disabled============
============guest<7> is disabled============
============guest<8> is disabled============
Chain ‘FORWARD_WIFI’ doesn’t exist.
Chain ‘INPUT_WIFI’ doesn’t exist.
rc_cmd=/usr/sbin/rc lanip start init
rc_cmd=/usr/sbin/rc firewall start
ScDrvDev_ioctl: CMD: (20) is not supported
rc_cmd=rc radvd restart
[Jan 01 00:00:31] radvd: no linklocal address configured for br0
[Jan 01 00:00:31] radvd: can’t join ipv6-allrouters on br0
iptables: Bad rule (does a matching rule exist in that chain?).
rc_cmd=/usr/sbin/rc networkmap start init
rc_cmd=/usr/sbin/rc qtbl start
rc_cmd=/usr/sbin/rc qos start
rc_cmd=/usr/sbin/rc cpm start init
rc_cmd=/usr/sbin/rc wanip stop 1
rc_cmd=/usr/sbin/rc dnrd stop wid 1
rc_cmd=/usr/sbin/rc hw_nat stop 1
rc_cmd=/usr/sbin/rc qtbl stop 1
rc_cmd=/usr/sbin/rc wanip stop 0
rc_cmd=/usr/sbin/rc dnrd stop wid 0
rc_cmd=/usr/sbin/rc hw_nat stop 0
rc_cmd=/usr/sbin/rc dnrd stop wid 1
rc_cmd=/usr/sbin/rc hw_nat stop 1
rc_cmd=/usr/sbin/rc qtbl stop 0
rc_cmd=/usr/sbin/rc dnrd stop wid 0
Tue Mar 10 21:04:28 UTC 2020
rc_cmd=/usr/sbin/rc qtbl stop 1
rc_cmd=/usr/sbin/rc ntp restart 0
rc_cmd=/usr/sbin/rc httpd start
rc_cmd=/usr/sbin/rc hw_nat stop 0
rc_cmd=/usr/sbin/rc qtbl stop 0
rc_cmd=/usr/sbin/rc coredump start
rc_cmd=/usr/sbin/rc redirect start
sh: /usr/sbin/uevent: not found
rc_cmd=/usr/sbin/rc dnrd start redirect
rc_cmd=/usr/sbin/rc ieee_802_1x start
bind: Address already in use
bind: Address already in use
rc_cmd=/usr/sbin/rc srt restart
rc_cmd=/usr/sbin/rc rp start
Mar/10/2020 21:04:28: dhcp6_ctl_authinit: failed to open /tmp/dhcp6sctlkey: No such file or directory
rc_cmd=/usr/sbin/rc udpecho start
rc_cmd=/usr/sbin/rc ingress_qos start
ScDrvDev_ioctl: CMD: (19) is not supported
/usr/sbin/iq: failed to enable Ingress QoS
rc_cmd=/usr/sbin/rc ingress_classify start
rc_cmd=/usr/sbin/rc qos_remark start
rc_cmd=/usr/sbin/rc ipv6wd start
rc_cmd=/usr/sbin/rc pppoe_relay start
rc_cmd=/usr/sbin/rc telnetd start
rc_cmd=/usr/sbin/rc sshd start
rc_cmd=/usr/sbin/rc igd_upnp start
rc_cmd=/usr/sbin/rc dnsr start
rc_cmd=/usr/sbin/rc cron start
Could not load host key: /etc/ssh/ssh_host_ed25519_key

rc_cmd=/usr/sbin/rc cwmp_stun start

Erasing 128 Kibyte @ 20000 — 0 % complete
Erasing 128 Kibyte

Smart Box GIGA login:

[ 0.000000] Linux version 5.15.45 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r19735+5-39bc566310) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Mon Jun 20 14:55:19 2022
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Beeline SmartBox GIGA
[ 0.000000] Initrd not found or empty — disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 11 pages/cpu s15632 r8192 d21232 u45056
[ 0.000000] pcpu-alloc: s15632 r8192 d21232 u45056 alloc=11*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=000380a8
[ 0.000000] Readback ErrCtl register=000380a8
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 248772K/262144K available (7068K kernel code, 621K rwdata, 1440K rodata, 1228K init, 242K bss, 13372K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.016023] Calibrating delay loop… 586.13 BogoMIPS (lpj=2930688)
[ 0.088357] pid_max: default: 32768 minimum: 301
[ 0.097730] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.112145] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.130589] rcu: Hierarchical SRCU implementation.
[ 0.140413] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.156011] smp: Bringing up secondary CPUs …
[ 0.165786] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.165812] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.165827] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.165872] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.225800] Synchronize counters for CPU 1: done.
[ 0.288061] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.288081] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.288092] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.288121] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.347009] Synchronize counters for CPU 2: done.
[ 0.407371] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.407392] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.407403] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.407434] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.466603] Synchronize counters for CPU 3: done.
[ 0.526208] smp: Brought up 1 node, 4 CPUs
[ 0.538542] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.558037] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.571871] pinctrl core: initialized pinctrl subsystem
[ 0.583441] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.596168] cpuidle: using governor teo
[ 0.614746] FPU Affinity set after 11720 emulations
[ 0.626530] clocksource: Switched to clocksource GIC
[ 0.637189] NET: Registered PF_INET protocol family
[ 0.647037] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.662026] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.678585] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.693755] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.707943] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.720649] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.733544] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.747664] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.758824] PCI: CLS 0 bytes, default 32
[ 0.769070] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.786216] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.797754] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.821429] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.832829] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.844204] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.855793] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.869076] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 0.886565] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 0.902755] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.156516] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.170266] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.179927] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.189628] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.203780] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.216298] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.227185] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.240822] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.253145] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.265022] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.277467] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.289969] pci 0000:00:00.0: supports D1
[ 1.297837] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.310068] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.321949] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.334372] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.346905] pci 0000:00:01.0: supports D1
[ 1.354738] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.368070] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.383899] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.400065] pci 0000:01:00.0: [14c3:7663] type 00 class 0x000280
[ 1.411935] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.426235] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.440581] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.455027] pci 0000:01:00.0: supports D1 D2
[ 1.463384] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.476567] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.507519] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.517810] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.529894] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.543373] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.557719] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.571110] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[ 1.582961] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 1.595506] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 1.608903] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.619187] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.631274] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.644755] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref]
[ 1.659098] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.672283] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.685363] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.699187] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.712315] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.726139] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.739628] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[ 1.753963] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[ 1.767449] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x604fffff pref]
[ 1.781780] pci 0000:00:00.0: BAR 1: assigned [mem 0x60500000-0x6050ffff]
[ 1.795272] pci 0000:00:01.0: BAR 1: assigned [mem 0x60510000-0x6051ffff]
[ 1.808753] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
[ 1.820832] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.832939] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[ 1.848327] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[ 1.863698] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[ 1.879088] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.888921] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.901018] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.914493] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 1.928844] pci 0000:02:00.0: BAR 0: assigned [mem 0x60300000-0x603fffff]
[ 1.942319] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.952162] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 1.964255] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 1.977738] pci 0000:00:01.0: bridge window [mem 0x60400000-0x604fffff pref]
[ 1.994203] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 2.008425] printk: console [ttyS0] disabled
[ 2.016918] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 2.034841] printk: console [ttyS0] enabled
[ 2.051380] printk: bootconsole [early0] disabled
[ 2.070929] 1e000e00.uartlite3: ttyS1 at MMIO 0x1e000e00 (irq = 20, base_baud = 3125000) is a 16550A
[ 2.092091] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[ 2.104816] nand: Macronix MX30LF1G18AC
[ 2.112465] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.127568] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 2.198194] scpart: Valid ‘SC PART MAP’ (12 partitions) found at 0x100000
[ 2.211806] 12 scpart partitions found on MTD device mt7621-nand
[ 2.223774] Creating 12 MTD partitions on «mt7621-nand»:
[ 2.234363] 0x000000000000-0x000000100000 : «u-boot»
[ 2.255576] 0x000000100000-0x000000200000 : «dynamic partition map»
[ 2.279221] 0x000000200000-0x000000300000 : «Factory»
[ 2.300657] 0x000000300000-0x000000400000 : «Boot Flag»
[ 2.322299] 0x000000400000-0x000000a00000 : «kernel»
[ 2.393738] 0x000000a00000-0x000001000000 : «Kernel 2»
[ 2.465496] 0x000001000000-0x000002800000 : «File System 1»
[ 2.719666] 0x000002800000-0x000004000000 : «File System 2»
[ 2.973870] 0x000004000000-0x000004800000 : «Configuration/log»
[ 3.067460] 0x000004800000-0x000005400000 : «application tmp buffer (Ftool)»
[ 3.203715] 0x000005400000-0x000007c00000 : «container»
[ 3.618659] 0x000007c00000-0x000007f80000 : «bad block reserved»
[ 3.674797] Concatenating MTD devices:
[ 3.682381] (0): «File System 1»
[ 3.688835] (1): «Configuration/log»
[ 3.695942] (2): «application tmp buffer (Ftool)»
[ 3.705300] (3): «container»
[ 3.711033] into device «ubi-concat»
[ 3.718219] 1 fixed-partitions partitions found on MTD device ubi-concat
[ 3.731561] Creating 1 MTD partitions on «ubi-concat»:
[ 3.741799] 0x000000000000-0x000005400000 : «ubi»
[ 4.618065] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 4.634307] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22
[ 4.652193] i2c_dev: i2c /dev entries driver
[ 4.663791] NET: Registered PF_INET6 protocol family
[ 4.675752] Segment Routing with IPv6
[ 4.683218] In-situ OAM (IOAM) with IPv6
[ 4.691146] NET: Registered PF_PACKET protocol family
[ 4.701671] 8021q: 802.1Q VLAN Support v1.8
[ 4.715700] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 4.750738] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 4.767498] mt7530 mdio-bus:1f: Link is Up — 1Gbps/Full — flow control rx/tx
[ 4.777321] mt7530 mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=24)
[ 4.803747] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=25)
[ 4.825826] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=26)
[ 4.848607] DSA: tree 0 setup
[ 4.857459] UBI: auto-attach mtd12
[ 4.864266] ubi0: attaching mtd12
[ 6.569075] ubi0: scanning is finished
[ 6.593617] ubi0: attached mtd12 (name «ubi», size 84 MiB)
[ 6.604622] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 6.618350] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 6.631872] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 6.645738] ubi0: good PEBs: 672, bad PEBs: 0, corrupted PEBs: 0
[ 6.657713] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 6.672098] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1655623215
[ 6.690300] ubi0: available PEBs: 0, total reserved PEBs: 672, PEBs reserved for bad PEB handling: 14
[ 6.708693] ubi0: background thread «ubi_bgt0d» started, PID 275
[ 6.711235] block ubiblock0_0: created from ubi0:0(rootfs)
[ 6.731676] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 6.752514] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 6.770858] Freeing unused kernel image (initmem) memory: 1228K
[ 6.782731] This architecture does not have kernel memory protection.
[ 6.795574] Run /sbin/init as init process
[ 6.803731] with arguments:
[ 6.803739] /sbin/init
[ 6.803745] with environment:
[ 6.803750] HOME=/
[ 6.803755] TERM=linux
[ 7.365183] init: Console is alive
[ 7.372435] init: — watchdog —
[ 8.332389] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 8.466740] usbcore: registered new interface driver usbfs
[ 8.477871] usbcore: registered new interface driver hub
[ 8.488611] usbcore: registered new device driver usb
[ 8.509742] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
[ 8.524831] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
[ 8.540216] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 8.550867] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 8.576708] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[ 8.595003] xhci-mtk 1e1c0000.xhci: irq 21, io mem 0x1e1c0000
[ 8.607769] hub 1-0:1.0: USB hub found
[ 8.615399] hub 1-0:1.0: 2 ports detected
[ 8.624157] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 8.634900] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 8.649895] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 8.662782] usb usb2: We don’t know the algorithms for LPM for this host, disabling LPM.
[ 8.679958] hub 2-0:1.0: USB hub found
[ 8.687616] hub 2-0:1.0: 1 port detected
[ 8.703072] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.736985] init: — preinit —
[ 9.522222] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.606264] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.656715] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.934957] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 9.951508] mtk_soc_eth 1e100000.ethernet eth0: Link is Up — 1Gbps/Full — flow control rx/tx
[ 9.956803] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 9.981979] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.186775] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 12.198447] UBIFS (ubi0:1): background thread «ubifs_bgt0_1» started, PID 411
[ 12.281452] UBIFS (ubi0:1): recovery needed
[ 12.499502] UBIFS (ubi0:1): recovery completed
[ 12.508528] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name «rootfs_data»
[ 12.524125] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 12.543868] UBIFS (ubi0:1): FS size: 76185600 bytes (72 MiB, 600 LEBs), max 610 LEBs, journal size 3809280 bytes (3 MiB, 30 LEBs)
[ 12.567083] UBIFS (ubi0:1): reserved for root: 3598434 bytes (3514 KiB)
[ 12.580250] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 4BBF3597-B4DE-421F-B3F1-C51DFE70CDB8, small LPT model
[ 12.607152] mount_root: switching to ubifs overlay
[ 12.635540] urandom-seed: Seeding with /etc/urandom.seed
[ 12.772907] procd: — early —
[ 12.778960] procd: — watchdog —
[ 13.446721] procd: — watchdog —
[ 13.560504] procd: — ubus —
[ 13.710652] urandom_read_iter: 7 callbacks suppressed
[ 13.710688] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.735591] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.748841] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.768157] procd: — init —
[ 14.624537] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.833207] urngd: v1.0.2 started.
[ 14.931610] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace
[ 14.946807] Backport generated by backports.git v5.15.33-1-0-g183c4ab2
[ 15.038797] random: crng init done
[ 15.045595] random: 23 urandom warning(s) missed due to ratelimiting
[ 15.143708] pci 0000:00:01.0: enabling device (0000 -> 0003)
[ 15.155088] mt7603e 0000:02:00.0: enabling device (0000 -> 0002)
[ 15.167298] mt7603e 0000:02:00.0: ASIC revision: 76030010
[ 16.207876] mt7603e 0000:02:00.0: Firmware Version: ap_pcie
[ 16.219025] mt7603e 0000:02:00.0: Build Time: 20160107100755
[ 16.266532] mt7603e 0000:02:00.0: firmware init done
[ 16.445876] ieee80211 phy0: Selected rate control algorithm ‘minstrel_ht’
[ 16.457434] pci 0000:00:00.0: enabling device (0000 -> 0003)
[ 16.468780] mt7615e 0000:01:00.0: enabling device (0000 -> 0002)
[ 16.494972] ieee80211 phy1: Selected rate control algorithm ‘minstrel_ht’
[ 16.549218] PPP generic driver version 2.4.2
[ 16.559854] NET: Registered PF_PPPOX protocol family
[ 16.578770] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 18.142125] mt7615e 0000:01:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin
[ 18.293080] mt7615e 0000:01:00.0: HW/SW Version: 0x65322d31, Build Time: 2009041715da1a1
[ 18.293080]
[ 18.470291] mt7615e 0000:01:00.0: N9 Firmware Version: 7663mp1827, Build Time: 20200904171623
[ 18.487408] mt7615e 0000:01:00.0: Region number: 0x3
[ 18.497403] mt7615e 0000:01:00.0: Parsing tailer Region: 0
[ 18.511604] mt7615e 0000:01:00.0: Region 0, override_addr = 0x00112c00
[ 18.524762] mt7615e 0000:01:00.0: Parsing tailer Region: 1
[ 18.536869] mt7615e 0000:01:00.0: Parsing tailer Region: 2
[ 18.548318] mt7615e 0000:01:00.0: override_addr = 0x00112c00, option = 3
[ 25.442218] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 25.468985] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 25.485622] mtk_soc_eth 1e100000.ethernet eth0: Link is Up — 1Gbps/Full — flow control rx/tx
[ 25.489096] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 25.517463] br-lan: port 1(lan1) entered blocking state
[ 25.527976] br-lan: port 1(lan1) entered disabled state
[ 25.540614] device lan1 entered promiscuous mode
[ 25.549938] device eth0 entered promiscuous mode
[ 25.564068] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 25.602056] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 25.617404] br-lan: port 2(lan2) entered blocking state
[ 25.627915] br-lan: port 2(lan2) entered disabled state
[ 25.640752] device lan2 entered promiscuous mode
[ 25.696679] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 810.414812] mt7530 mdio-bus:1f lan1: Link is Up — 1Gbps/Full — flow control rx/tx
[ 810.429836] br-lan: port 1(lan1) entered blocking state
[ 810.440275] br-lan: port 1(lan1) entered forwarding state
[ 810.451901] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready

Характеристики

1.Сохранить оригинальную прошивку.

cd /mnt/shares/sda/A

вместо sda может быть sd*, вместо A возможен вариант B или C и т.д.

проверить можно командами ls /mnt/shares/ и ls /mnt/shares/sda/

    chmod 755 busybox-mipsel

    mkdir mtd_backup

    ./busybox-mipsel dd if=/dev/mtdblock0 of=/mnt/shares/sda/A/mtd_backup/mtd0

    ./busybox-mipsel dd if=/dev/mtdblock1 of=/mnt/shares/sda/A/mtd_backup/mtd1

    ./busybox-mipsel dd if=/dev/mtdblock2 of=/mnt/shares/sda/A/mtd_backup/mtd2

    ./busybox-mipsel dd if=/dev/mtdblock3 of=/mnt/shares/sda/A/mtd_backup/mtd3

    ./busybox-mipsel dd if=/dev/mtdblock4 of=/mnt/shares/sda/A/mtd_backup/mtd4

    ./busybox-mipsel dd if=/dev/mtdblock5 of=/mnt/shares/sda/A/mtd_backup/mtd5

    ./busybox-mipsel dd if=/dev/mtdblock6 of=/mnt/shares/sda/A/mtd_backup/mtd6

    ./busybox-mipsel dd if=/dev/mtdblock7 of=/mnt/shares/sda/A/mtd_backup/mtd7

    ./busybox-mipsel dd if=/dev/mtdblock8 of=/mnt/shares/sda/A/mtd_backup/mtd8

    ./busybox-mipsel dd if=/dev/mtdblock9 of=/mnt/shares/sda/A/mtd_backup/mtd9

    ./busybox-mipsel dd if=/dev/mtdblock10 of=/mnt/shares/sda/A/mtd_backup/mtd10

    ./busybox-mipsel dd if=/dev/mtdblock11 of=/mnt/shares/sda/A/mtd_backup/mtd11

    ./busybox-mipsel dd if=/dev/mtdblock2 of=/mnt/shares/sda/A/mtd_backup/eeprom.bin count=512

вывод будет примерно таким:

    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock0 of=/mnt/shares/sda/A/mtd_backup/mtd0

    2048+0 records in

    2048+0 records out

    1048576 bytes (1.0MB) copied, 3.480980 seconds, 294.2KB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock1 of=/mnt/shares/sda/A/mtd_backup/mtd1

    2048+0 records in

    2048+0 records out

    1048576 bytes (1.0MB) copied, 0.303034 seconds, 3.3MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock2 of=/mnt/shares/sda/A/mtd_backup/mtd2

    2048+0 records in

    2048+0 records out

    1048576 bytes (1.0MB) copied, 0.302884 seconds, 3.3MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock3 of=/mnt/shares/sda/A/mtd_backup/mtd3

    2048+0 records in

    2048+0 records out

    1048576 bytes (1.0MB) copied, 0.302910 seconds, 3.3MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock4 of=/mnt/shares/sda/A/mtd_backup/mtd4

    12288+0 records in

    12288+0 records out

    6291456 bytes (6.0MB) copied, 1.930418 seconds, 3.1MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock5 of=/mnt/shares/sda/A/mtd_backup/mtd5

    12288+0 records in

    12288+0 records out

    6291456 bytes (6.0MB) copied, 2.014378 seconds, 3.0MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock6 of=/mnt/shares/sda/A/mtd_backup/mtd6

    49152+0 records in

    49152+0 records out

    25165824 bytes (24.0MB) copied, 9.886928 seconds, 2.4MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock7 of=/mnt/shares/sda/A/mtd_backup/mtd7

    49152+0 records in

    49152+0 records out

    25165824 bytes (24.0MB) copied, 9.167029 seconds, 2.6MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock8 of=/mnt/shares/sda/A/mtd_backup/mtd8

    16384+0 records in

    16384+0 records out

    8388608 bytes (8.0MB) copied, 2.591018 seconds, 3.1MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock9 of=/mnt/shares/sda/A/mtd_backup/mtd9

    24576+0 records in

    24576+0 records out

    12582912 bytes (12.0MB) copied, 3.898485 seconds, 3.1MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock10 of=/mnt/shares/sda/A/mtd_backup/mtd10

    81920+0 records in

    81920+0 records out

    41943040 bytes (40.0MB) copied, 17.527277 seconds, 2.3MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock11 of=/mnt/shares/sda/A/mtd_backup/mtd11

    7168+0 records in

    7168+0 records out

    3670016 bytes (3.5MB) copied, 1.062676 seconds, 3.3MB/s


    /mnt/shares/sda/A # ./busybox-mipsel dd if=/dev/mtdblock2 of=/mnt/shares/sda/A/mtd_backup/eeprom.bin count=512

    512+0 records in

    512+0 records out

    262144 bytes (256.0KB) copied, 0.146274 seconds, 1.7MB/s

Если все сделали верно на флешке появиться директория «mtd_backup», в ней наши файлы mtd. Сохраните эти файлы в надежное место!

Содержание

1. Технические характеристики версий
2. Индикаторы и кнопки
3. Подключение и вход в админку
4. Автоматическая настройка
5. Ручная настройка
6. Настройка на другого провайдера
7. USB модем
8. Настройка USB
9. Wi-Fi
10. IPTV
11. Прошивка
12. Сброс