Скачать прошивку для роутера asus rt ac51u

— Release Note —

Security Fixes
— Fixed CVE-2015-6949 buffer overflow issue, special thanks for Elvis Collado at DVLabs.
— Fixed Web server Accept-Language buffer overflow, special thanks for Elvis Collado at Praetorian.
— Fixed Web server URL handler buffer overflow, special thanks for Elvis Collado at Praetorian.
— Enhanced router login password and wireless password(WPA2) strength check method to against brute-force attack.
— Reject administrator to set too easy to guess login and wireless password to avoid brute-force attack.

New Features
— Time scheduling, Wireless MAC filter client drop down menu can show offline devices.

Modifications
— Added Meo and Movistar ISP profile.
— Adjusted Guest network mac filter maximum client number to 16
— Allow paste password on login page to fulfil some password management softwares requirement.
— Show current control channel while value is auto.
— Bandwidth limiter can accept decimal point.
— Unnecessary to reboot router after set allow only spcified IP address to enter GUI.
— Adaptive QoS can now be enabled without assigned upload/ download bandwidth.

Fixes
— Fixed setup wizard IE11 compatibility issue.
— Fixed Adaptive QoS game mode GUI issue.
— Fixed Traffic Analyzer GUI issue.
— Fixed OpenVPN connection status display error.

Easiest solution for Windows users, confirmed working as of June 2019.

1. Download the ASUS Firmware Restoration Tool but don’t open it yet (Recommended version)

2. Unplug your computer from the router

3. Put the router into Rescue Mode by: turning the power off, using a pin to press and hold the reset button, then turning the router back on while keeping the reset button pressed for ~5 secs until the power LED starts flashing slowly (which indicates the router has entered Rescue Mode)

4. Important (if you don’t do this next step the Asus Firmware Restoration Tool will wrongly assume that the router is not in Rescue Mode and will refuse to flash it): go to the Windows Control Panel and temporarily disable ALL other network adapters except the one you will use to connect your computer to the router

5. For the single adapter you left enabled, temporarily give it the static IP 192.168.1.10 and the subnet mask 255.255.255.0

6. Connect a LAN cable between your computer (make sure to use the Ethernet port of the adapter you’ve just set up) and port 1 of the router (not the router’s WAN port)

7. Rename openwrt-XX.XX.X-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin to factory.trx

8. Open the Asus Firmware Restoration Tool, locate factory.trx and click upload (if Windows shows a compatibility prompt, confirm that the tool worked fine)

9. Flashing and reboot is finished when the power LED stops blinking and stays on

10. That’s it! (Don’t forget to re-enable any network adapters you disabled earlier)

See also Asus ‘How to use Rescue Mode’ FAQ

1. Download the OpenWrt firmware image

2. Unplug the power cord from the router

3. Press the reset button with a pin and keep holding it down

4. Plug the power cord in

5. Wait 10 seconds

6. Release the reset button

7. On your computer, set *this* static IP to the network adapter connected to the router (IP 192.168.1.75, Subnet 255.255.255.0, connect to the first LAN port of the router)

8. Use tftp -client to download the firmware image

       tftp> binary
       tftp> timeout 120
       tftp> connect
       (to) 192.168.1.1
       tftp> put openwrt-XX.XX.X-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin

9. The power LED flashes quickly while the router is being flashed

10. Flashing is successful when the power LED is constantly lit

Note: Depending on your firmware version, you might have to re-install LuCI and any extraneous packages after the upgrade